The purpose of caution tapes is to warn against certain risks. Some people use caution tapes interchangeably with danger tapes, depending on the preference of the consumer, caution tapes, on the other hand, are typically used to alert workers who work in hazardous situations or areas to proceed with caution, while danger tapes prevent people from entering dangerous places where they could be seriously injured or killed.Danger TapeThe majority of people confuse danger tape with caution tape, even though the intended use of these two products is quite different. Designed to grab the attention of those around them, these adhesive-free, bright-colored tapes reduce the possibility of serious injury to everyone in the area, ensuring everyone's safety at all times.On barricade tapes, you will typically find warnings about caution, danger, and lead hazards. They are mainly used to promote safety in hazardous areas. Tensile Strength (Longitudinal): 2425 psiSafety & Hazard Tapes A variety of caution, hazard, and danger tapes convey safety warnings in and around work sites. Material Identification: Nominal 3 Mil Polyethylene, 3" & 6" wide Unless otherwise noted, all tests are run at 23☌ (73☏) and 50% R.H. Tensile Modulus, 1% Secant: TD= SI Units: 222 MPa, Customary Units: 32,000 psi, Method, ASTM: D882īlown Film Preparation & Conditions: Extrusion conditions used to produce film include a 2.4:1 blow-up ratio and 8.0 lb/hr/inch die output. Tensile Modulus, 1% Secant: MD= SI Units: 208 MPa, Customary Units: 30,000 psi, Method, ASTM: D882 Elongation Break: TD= SI Units: 850 %, Customary Units: 850 %, Method, ASTM: D882 Elongation Break: MD= SI Units: 650 %, Customary Units: 650 %, Method, ASTM: D882 Tensile Strength Yield: TD= SI Units: 9.7 MPa, Customary Units: 1,400 psi, Method, ASTM: D882 Tensile Strength Yield: MD= SI Units: 10 MPa, Customary Units: 1,450 psi, Method, ASTM: D882 Tensile Strength Break: TD= SI Units: 35 MPa, Customary Units: 5,000 psi, Method, ASTM: D882 Tensile Strength Break: MD= SI Units: 49 MPa, Customary Units: 7,000 psi, Method, ASTM: D882 Elmendorf Tear Resistance: TD= SI Units: 600 g, Customary Units: 600 g, Method, ASTM: D1922 Elmendorf Tear Resistance: MD= SI Units: 400 g, Customary Units: 400 g, Method, ASTM: D1922 Seal Initiation Temp.: SI Units: 99☌, Customary Units: 210☏, Method, ASTM: Eastman Dart Impact: SI Units: 200 g, Customary Units: 200 g, Method, ASTM: D1709A Gloss (Gardner Rating 45?): SI Units: 40, Customary Units: 40, Method, ASTM: D2457 Haze: SI Units: 20%, Customary Units: 20%, Method, ASTM: D1003 Density: SI Units: 917 kg/m3, Customary Units: 0.917 g/cc, Method, ASTM: D4883 Melt Index (condition 190/2.6): SI Units: 1.0 g/10 min, Customary Units:1.0 g/10 min. Tapes help prevent accidents by increasing visibility of hazards and can be tied, stapled or nailed in place. Standard letter height is two inches (2"). 2 mils, 3, mils, or 4 mils.īarricade warning tapes will consist of high visibility safety yellow or red polyethylene with bold black letters. Also available in 200 ft., 300 ft., and 500 ft. Meets OSHA 1910.144 for marking physical hazards.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |